Страница 1 из 1

S29GL064N90TFI04

Добавлено: Пн июн 09, 2014 6:02 pm
Asu
Ezo Hello, I want to program flash S29GL064N90, I read the flash but do not know which settings to schedule, please is my 1st time schedule, be patient.

regards

Re: S29GL064N90TFI04

Добавлено: Пн июн 09, 2014 7:01 pm
Asu
If I choose S29AL008D: I read 100% but not recorded, it is tried to record more than 20minutes and 0%
And Tsop_48_D3 Ezoflash adapter +4.4
Pj2 On
Jp1, 3 y 4 off
JpB, F y H On
JpA, C y D Off

Electronic ID:
Willem
manufacture 0x00
Device Code 0xF0

Erase16
EZoFlash4v4 detected !
#READ[00]=0x8007

#MAN.ID =0x8007
#DEV.ID =0x2B07

Re: S29GL064N90TFI04

Добавлено: Чт июн 12, 2014 5:14 pm
Ezo
Read S29GL128 programming guide. http://www.ezoflash.com/adapters/tsop48 ... _guide.pdf
Apply 0.97d12 or 0.98d12 Sw depending of hw
tspop48d3, Select 16bit Am29DL322 or 16bit 29F320.
More info in guide.
Read related topics - search S29GL064, 29LV640 ,...

Re: S29GL064N90TFI04

Добавлено: Вс июл 13, 2014 3:52 pm
Asu
Ezo писал(а):Read S29GL128 programming guide. http://www.ezoflash.com/adapters/tsop48 ... _guide.pdf
Apply 0.97d12 or 0.98d12 Sw depending of hw
tspop48d3, Select 16bit Am29DL322 or 16bit 29F320.
More info in guide.
Read related topics - search S29GL064, 29LV640 ,...
Willem Eeprom 97D12c2, Ezoflash4+4

Tsop48_b2 Selecte device 29VF/39LF/VF/49LFxxx 29LV320

regards

Re: S29GL064N90TFI04

Добавлено: Пн июл 14, 2014 9:43 pm
Ezo
Generally tsop48d3 recomended in 16bit mode. We can do with tsop48b2.
You have tsop48b2 (8/16 bit mode) and valid ID reply with 29LV320 selected 0x01 AMD 0x7E :)
Find central pin on adapter jumper block Jp7/8/9 connected to chip pin13 A21.
No jumpers, central pin grounded to operate read 0-32Mb, erase entire chip, write 0-32Mb
Apply JP7 (pin13=log1) read 32-64Mb, write 32-64Mb

Re: S29GL064N90TFI04

Добавлено: Пт июл 18, 2014 3:13 pm
Asu
Thanks Ezo, forgive my English is not good.
I have programmed a 8Mb file and the two files did Winsplit application 4Mb. JP9 0-4 Mb JP7 4-8 Mb is correct?

You mean JP9 I burn a 32Mb file? not understand and appreciate your explanation.

regards

Re: S29GL064N90TFI04

Добавлено: Пт июл 18, 2014 8:47 pm
Ezo
Jp9 is providing log0, but not sure on all SW versions , like 0.97..
With 0.98 adress are groupped in 3x8 blocks, highest non used log.0
With 0.97 (some Sw versions) adress lenght adapted to chip size.
I recomend write/verify 0-32Mb with Jp9 , then verify with central pin grounded

Re: S29GL064N90TFI04

Добавлено: Пт июл 18, 2014 8:56 pm
Asu
Thanks Ezo, now I have mounted flash adapter Tsop48_b2 EON29LV640B-90. JP9 (central pin) and 0.97-I write and verify 8Mb file OK.

regards

Re: S29GL064N90TFI04

Добавлено: Вт июл 22, 2014 9:18 pm
Asu
Ezo писал(а):Jp9 is providing log0, but not sure on all SW versions , like 0.97..
With 0.98 adress are groupped in 3x8 blocks, highest non used log.0
With 0.97 (some Sw versions) adress lenght adapted to chip size.
I recomend write/verify 0-32Mb with Jp9 , then verify with central pin grounded

Hello Ezo.
To work with Flash Eon29LV640B - MX29LV640DB and S29GL064N90TFI04 in Device Select 29LV320 but we have to select when choosing this software 29LV320 we can only write to the address 3FFFFF0 (only 4,196 Mb)
Please, I would like to know how to write 8Mb, with Ezoflash4 +4 and Tsop48_b2.

Re: S29GL064N90TFI04

Добавлено: Ср июл 23, 2014 7:15 am
Ezo
Central adapter jumper pin is connected to chip highest adress A21.
Pin with log0 (grounded),access to chip 0-32Mb.
Pin with log1 (via resistor to 3.3V Vcc) access to chip 0-64Mb.
A21-0 to get ID, read 0-32Mb, erase entire chip, write 0-32Mb
A21-1 to read 32-64Mb, write 32-64Mb.
Source 64Mb file split in 2 parts.
About split read my doc S29GL128 programming guide.

Re: S29GL064N90TFI04

Добавлено: Ср июл 23, 2014 8:27 am
Asu
I am not talking of the adapter, I talk about software 0.97D12 Willem Eprom if Habres 8MB file to write jumper JP9 (0-32 Mb) just write 4Mb.
If you read JP9 (0-32 Mb) only reads 4 Mb

attached some pictures for you to understand me.


regards

Re: S29GL064N90TFI04

Добавлено: Ср июл 23, 2014 8:29 am
Asu
Archive 8 Mg, single program 4 mb

What is the solution?

Re: S29GL064N90TFI04

Добавлено: Ср июл 23, 2014 6:57 pm
Ezo
I am not talking of the adapter, I talk about software 0.97D12 Willem Eprom if Habres 8MB file to write jumper JP9 (0-32 Mb) just write 4Mb.
If you read JP9 (0-32 Mb) only reads 4 Mb
Note , 32Mb (megabit)=4MB (megabyte)
Yes, SW allow operate with only 4MB (32Mb).
You have to work with each memory block (twice) , with apropriate selected highest adress

Re: S29GL064N90TFI04

Добавлено: Пт июл 25, 2014 9:19 pm
Asu
Thanks Ezo, now I see clearer