Willem PCB4.5C and 28F320 C3BA110

By: travolta - 2008-01-12 14:37:34

Hi,

I have a willem PCB4.5C and I'm trying to programm an Intel TE28F320 C3BA110 with a binary file (.bin) I can read and erase the chip but when I try to write to it, it schows alway an error writing to this address:

Error at 0X000080 Chip = 0x0010 buffer = 0x603c

I have the Programmer with Adapter and the TSOP48 16bit Mode adapter.

Can anyone help me and tell me whats wrong with the programmer or my chip.

Thanks

Re: Willem PCB4.5C and 28F320 C3BA110

By: travolta - 2008-01-12 14:52:43

ok, here you can see the programmer and the error:



the settings here are for 28F320 and not for the 29F as on this foto...




Re: Willem PCB4.5C and 28F320 C3BA110

By: EZo - 2008-01-12 16:22:04

1) SW 0.98d5 is pcb4.5c compatible. Your programmer looks like pcb3.5/pcb4.0c variant.
Try with software 0.97ja, jumpers in pcb3 mode (jumpers right).
You can try 0.98d2 in pcb3.5 mode too.
2) tsop48 adapter jumpers set according picture 28Fxxx
3) Do you apply cable between adapter and programmer for highest adress (A19, A20,..) ?
4) I am surprising how do use your Wells socket adapter (with 40 pins), you need T01 adapter.
5) Don't care on chip lock message. SW pass this lock, I wrote about this.

Re: Willem PCB4.5C and 28F320 C3BA110

By: travolta - 2008-01-13 11:36:11

Hello EZO,

thank you for your reply.

as I wrote, I have the PCB45 from SIVAVA. I have also the adapters (T01 and T07) both are connected to the Programmer with a rippon cable (8pins) I posted a wrong pic of the TSOP48 in my last post.... The jumpers for the TSOP48 are for 28FXXX as on board.

This is the right adapter:



I found this:

TE28F320C3B verified OK (read/erase/blank check/program/verify) on following devices below. SW 0.97ja, selected device 16bit 28F320C3B. Get ID 0x0089 Intel, 0x88C5 28F320C3B. CFI Query present. Program/verify time about 20min. Option 28Fxxx sector lock/unlock not activ, status are lock for all sectors.
1)ezoflash+(v4.3)/tsop48d1 (or tsop48d2 with JpAA). Jumpers Jp2(Vcc=3.6V), Jp5(A18 )
2)PCB3B/sivava T01/T07. PCB3B jumpers J1 2-5 (default,A13), J2 1-5 (default,A11), J3 2-3 (pin1 Vpp), J6 1-2 and J7 2-3 (vpp=12.7V), J8 1-2 (Vcc=5V), dipswitch picture PCB3 3-5-6-8-10-12 on, full 8wire cable from programmer J4 to adapter. T07 jumpers as shown on adapter for 28Fx00, Jp open=3.6V removed.
3) W3.1/sivava T01/T07. W3.1 jumper normal (normal/29x040), power switch 1-2 on (Vpp=12.7V), dipswitch picture Willem 3-5-6-8-10-12 on. A19 (on 6pin connector) connected to adapter connector pin 7 (A19), A20 (on 6pin connector) connected to adapter connector pin 5 (A20).  T07 jumpers as shown on adapter for 28Fx00, Jp open=3.6V removed.
4) W4.0/sivava T01/T07. W4.0 jumpers Vpp(Vpp/A18,A19), normal (normal/erase), powerswitch 2 on (Vpp=12.7) and 4 on (Vcc=3.3V), dipswitch picture PCB3 3-5-6-8-10-12 on. A19 ( Jp2 pin4) connected to adapter connector pin 7 (A19), A20 (Jp2 pin5) connected to adapter connector pin 5 (A20). T07 jumpers as shown on adapter for 28Fx00, Jp open=3.6V closed.

Can you please tell me if you mean by JP1 1-5 ( I have to connect these Jumpers (Also 1-2 3-4 and 5) or to let the default settings like in the first picture from the programmer?


Thanks

Re: Willem PCB4.5C and 28F320 C3BA110

By: EZo - 2008-01-13 12:12:03

Jumpers Jp1...8 are allocated on pcb45c equal to pcb3b. pcb45c has additional jumpers for mode (pcb45c/pcb3b) and voltage (open 3.6V).
Quote:
Can you please tell me if you mean by JP1 1-5
.
No, J1 2-5. Find pin , jumper and component allocation for pcb45c   here.
I am confused in your programmer- you mean pcb45c, but pictures are different. Does your programmer have chips 74HC540 and 4021 (specific for sivava pcb45c design) ?

Re: Willem PCB4.5C and 28F320 C3BA110

By: travolta - 2008-01-13 12:38:48

Hi EZO,

I think now I don't have any problems, I can read, erase and write the chips  

I followed the steps you mentioned and now it's working ok.

I have this Programmer here:

http://www.sivava.com/buynow.php?pd=A045

It's the PCB45C



and these adapters:

http://www.sivava.com/buynow.php?pd=T10



Thank you again.