programming pm49fl004t HELP ME

By: angelo - 2008-02-07 22:29:53

Hi dudes, i'm a noob, but i want learn a lot of these world!!!!!
i have a problem with my pcb4.5 i tried to programming pm49fl004t by willem eprom 0.98d5 but there was only pm49fl004, so i saw that there is a new software 0.98d8. this software have pm49fl004t device.. but i have the same problem the programming doesn't finish respond with error... the software see the hardware correctly, test hardware is OK, the program erase the pmc flash correctly: erase completed by check DQ7, i set the jumper naturally but nothing!!! where is my error?? i load a file of bios for a P4P800 deluxe.. and the answer is: loaded binary file OK.. i use usb power i see to website that is necessary 3.3v? is it correct?
the errors are:
1 配ime -> error at 0x012CB4 Chip = 0x0B buffer = 0xAB | without skip write 0xFF
2 配ime -> error at 0x03507B Chip = 0x28 buffer = 0x29 | with skip write 0xFF
3 配ime -> error at 0x009AB6 Chip = 0x34 buffer = 0x74 | with skip write 0xFF
4 配ime -> error at 0x03F68C Chip = 0x08 buffer = 0x0A | with skip write 0xFF
5 配ime -> error at 0x007AC2 Chip = 0xA1 buffer = 0xE9 | with skip write 0xFF
before any programming i erase the flash...



ps. potete rispondere anche e soprattutto in ita  

Re: programming pm49fl004t HELP ME

By: Drago - 2008-02-08 08:43:00

angelo wrote on 02/07/08 at 22:29:53:
Hi dudes, i'm a noob, but i want learn a lot of these world!!!!!
i have a problem with my pcb4.5 i tried to programming pm49fl004t by willem eprom 0.98d5 but there was only pm49fl004, so i saw that there is a new software 0.98d8. this software have pm49fl004t device.. but i have the same problem the programming doesn't finish respond with error... the software see the hardware correctly, test hardware is OK, the program erase the pmc flash correctly: erase completed by check DQ7, i set the jumper naturally but nothing!!! where is my error?? i load a file of bios for a P4P800 deluxe.. and the answer is: loaded binary file OK.. i use usb power i see to website that is necessary 3.3v? is it correct?
the errors are:
1 配ime -> error at 0x012CB4 Chip = 0x0B buffer = 0xAB | without skip write 0xFF
2 配ime -> error at 0x03507B Chip = 0x28 buffer = 0x29 | with skip write 0xFF
3 配ime -> error at 0x009AB6 Chip = 0x34 buffer = 0x74 | with skip write 0xFF
4 配ime -> error at 0x03F68C Chip = 0x08 buffer = 0x0A | with skip write 0xFF
5 配ime -> error at 0x007AC2 Chip = 0xA1 buffer = 0xE9 | with skip write 0xFF
before any programming i erase the flash...



ps. potete rispondere anche e soprattutto in ita   



Ciao angelo...

Dovresti anche inserire la sigla completa del chip, l'adattatore che hai usato, insomma dare pi羅 informazioni perch癡 non si capisce se il tuo chip ha case PLCC oppure VSOP, per la tensione 3.3/3.6 Volt mi sembrano corretti, secondo quanto recita il datasheet.

Ancora 癡 la prima volta che usi il programmatore?
癡 comprato oppure autocostruito?

translate with translator
Sorry for my wrong English

Hello angel...
You would have also to insert the complete acronym of the chip, the adapter that you have used, insomma to give more information why Volt is not understood if yours chip it has houses PLCC or VSOP, for 3.3/3.6 tension me seems corrected, second how much recites the datasheet.

Still it is before the time that uses the programmatore?
It is bought or auto constructed?

Re: programming pm49fl004t HELP ME

By: angelo - 2008-02-08 21:46:02

grandissimo!!!! e pensare che credevo di aver inserito tutto ma mi sbagliavo LOL allora io uso questo attrezzo http://www.sivava.com/img-ebay/pcb4-5c_construction-EBay.jpg non auto-costruito. Lo Willem EPROM PProgrammer PCB4.5C.
S穫 癡 la mia prima esperienza in questo campo e vorrei imparare tantissime cose. Ho cercato anche sul sito sivava.com ma non ho trovato nessuna guida su come farlo nello specifico.. a grandi linee ci sono lo ho fatto per簷 senza avere risultati di programming ma solo di erasing... il programma mi diceva di metterlo nello Zif (si dice cos穫?) PLCC Firmware HUB/LPC e non quello PLCC32. ANche perch癡 ho pensato dato che dovevo rimettere il bios su quel chip fosse corretto quello slot.
per la sigla c'癡 scritto quanto e come segue:
PMC Flash
MGQGY
0330
Pm49FL004T-33JC

tutto qua
spero che mi puoi aiutare soprattutto ad imparare ad usare questo magnifico attrezzo, anzi se mi puoi dire dove posso trovare delle guide diciamo fatte bene te ne sarei molto grato cos穫 da capirci qualcosa di pi羅   
grazie Drago!!!!!!!!!!!!!!!!!!!

translate:
hi dude,
i have these programmer http://www.sivava.com/img-ebay/pcb4-5c_construction-EBay.jpg my chip is:
PMC Flash
MGQGY
0330
Pm49FL004T-33JC
i used slot/zif (i don't know the exactly name..) PLCC Firmware HUB/LPC and not PLCC32, because the programmer's software there was wrotten to use firmware HUB...i thought that it was right because i must program a bios..
help me   
thx all!!!!

Re: programming pm49fl004t HELP ME

By: legleg - 2008-02-10 12:55:05

arf i am interesting with this question


I whant also reprograme pm49fl004t-33jc for A7n8x-E deluxe with cpu amd barton 3200....
my programmer  pcb4-5c and the logiciel is willem eprom 0.98d5

i work in the same reprogramming eprom... i arrive to read, erase, and program eprom with .bin (rev bios 1013) sin to move jumper...
but when i test it on my motherboard my cpu (barton 3200) is reconize just to 2500 barton ??? i don't know why ???  

haha its difficults to speak english i speak frenchglish lol  

Re: programming pm49fl004t HELP ME

By: angelo - 2008-02-10 13:01:58

oups lol

Re: programming pm49fl004t HELP ME

By: legleg - 2008-02-10 15:41:59

johnleg wrote on 02/10/08 at 12:55:05:
arf i am interesting with this question


I whant also reprograme pm49fl004t-33jc for A7n8x-E deluxe with cpu amd barton 3200....
my programmer   pcb4-5c and the logiciel is willem eprom 0.98d5

i work in the same reprogramming eprom... i arrive to read, erase, and program eprom with .bin (rev bios 1013) sin to move jumper...
but when i test it on my motherboard my cpu (barton 3200) is reconize just to 2500 barton ??? i don't know why ???   

haha its difficults to speak english i speak frenchglish lol   


did you finished the programming?????????? arghhhhhhhhhhhhhh why my chip not????
could you explain me your exactly full process???? thx you

Re: programming pm49fl004t HELP ME

By: legleg - 2008-02-10 16:04:20

ok for programming my eprom i do

- i identifie l'eeprom (its write on the eprom)
- i select it in the logiciel (0.98d5)
PMC Flash MH092 0339 Pm49FL004T-33JC => in  "Device"
=>"Firmware HUB / LPC => Pmc => Pm49FL004"

- i puch "cavalier idem that picture in logiciel (white cavalier)
- i put eeprom in programmer (in fwh/lpc)
- connect "printer port"
- connect usb ....
- verification of eeprom
- read eeprom
- save file with extension ex .bin
- erase eeprom
- load new bios
- programm eeprom
- read verification
- put your new eeprom in your motherboard

but i dont know why my cpu isn't reconiz at barton 3200 ??????  

Re: programming pm49fl004t HELP ME

By: angelo - 2008-02-10 18:36:24

heuuu question at 2euros lol  

when i have reprogramme an eeprom for test it i must use it on computer who his HDD and windows are not install ??? because now i test new eprom on my computer with xp and hdd who are install.....

Re: programming pm49fl004t HELP ME

By: angelo - 2008-02-12 20:24:17

johnleg wrote on 02/10/08 at 16:04:20:
ok for programming my eprom i do

- i identifie l'eeprom (its write on the eprom)
- i select it in the logiciel (0.98d5)
PMC Flash MH092 0339 Pm49FL004T-33JC => in   "Device"
=>"Firmware HUB / LPC => Pmc => Pm49FL004"

- i puch "cavalier idem that picture in logiciel (white cavalier)
- i put eeprom in programmer (in fwh/lpc)
- connect "printer port"
- connect usb ....
- verification of eeprom
- read eeprom
- save file with extension ex .bin
- erase eeprom
- load new bios
- programm eeprom
- read verification
- put your new eeprom in your motherboard



i did the same.. but   during the programming, the 0.98d5 took me error... :S

why???? do you have any ideas??

Re: programming pm49fl004t HELP ME

By: Drago - 2008-02-12 20:25:42

johnleg wrote on 02/10/08 at 16:04:20:
but i dont know why my cpu isn't reconiz at barton 3200 ??????   


you can try to change version bios... maybe it's only that version...

Re: programming pm49fl004t HELP ME

By: angelo - 2008-02-14 08:30:56

@Angelo...

Ciao

Io non ho il tuo stesso programmatore, ho costruito EZoflash v4.4

cmq da quello che leggo, il tuo chip dovrebbe essere con case VSOP e non PLCC, quindi credo tu debba inserire un adattatore che contenga il chip e poi infilarlo nel programmatore.

Dopo leggo la procedura di johnleg che mi sembra corretta per la riprogrammazione del chip uguale al tuo.

Dovresti verificare che il chip venga riconosciuto quando fai ID altrimenti 癡 inutile che provi a cancellare e/o riprogrammare.



P.S. documenti e guide sull'argomento non saprei dove tu possa trovarli, il consiglio 癡 di leggere il forum e cercare di capirci qualcosa.


@Angelo...
Hi
I do not have your same programmatore, I have constructed EZoflash v4.4 cmq from what I read, yours chip he would have to be with houses VSOP and not PLCC, therefore creed you must insert an adapter that contains the chip and then to thread it in the programmatore. After I read the procedure of johnleg that me it seems corrected for the re- program eprom of the chip equal yours. You would have to verify that the chip it comes recognized when you make ID otherwise is useless that tests to cancel and/or riprogrammare.

P.S. documents and guides on the argument I would not know where you can find them, the council is to read the forum and to try to understand something to us.

Re: programming pm49fl004t HELP ME

By: angelo - 2008-02-15 20:27:56

Drago wrote on 02/14/08 at 08:30:56:
@Angelo...

Ciao

Io non ho il tuo stesso programmatore, ho costruito EZoflash v4.4

cmq da quello che leggo, il tuo chip dovrebbe essere con case VSOP e non PLCC, quindi credo tu debba inserire un adattatore che contenga il chip e poi infilarlo nel programmatore.

Dopo leggo la procedura di johnleg che mi sembra corretta per la riprogrammazione del chip uguale al tuo.

Dovresti verificare che il chip venga riconosciuto quando fai ID altrimenti 癡 inutile che provi a cancellare e/o riprogrammare.



P.S. documenti e guide sull'argomento non saprei dove tu possa trovarli, il consiglio 癡 di leggere il forum e cercare di capirci qualcosa.


@Angelo...
Hi
I do not have your same programmatore, I have constructed EZoflash v4.4 cmq from what I read, yours chip he would have to be with houses VSOP and not PLCC, therefore creed you must insert an adapter that contains the chip and then to thread it in the programmatore. After I read the procedure of johnleg that me it seems corrected for the re- program eprom of the chip equal yours. You would have to verify that the chip it comes recognized when you make ID otherwise is useless that tests to cancel and/or riprogrammare.

P.S. documents and guides on the argument I would not know where you can find them, the council is to read the forum and to try to understand something to us.


ok grazie! stasera provo nn ricordo se lo avevo fatto!
ti faccio saper!!!
grazie di tutto per ora




*ok thx tonight i try. i don't remember if i recognize ID..
i'll tell you news!!!
thx all just now

Re: programming pm49fl004t HELP ME

By: EZo - 2008-02-15 21:50:24

ho fatto tutti i test, read chip, verify chip, id test, check blank chip.
tutto ok!!! rispettivamente quano segue: ok, ok, hardware present e ok .(ma cos'癡 il check blank chip???) da quanto sembra vede tutto fa tutto ma nn completa il programming... ma potrebbe essere rovinato il chip?? quante possibilit  ci sono che si rompa un chip???e soprattutto come fa a rompersi???? dopo tutte queste procedure ho naturalmente riprovato il programming.. ma niente...
ERROR AT 0x01F470 Chip = 0x08 buffer = 0x88...
che vuol dire??

i made all test.. read, verify, id check, check blank chip.. all ok (what is check blank chip?) naturally after test i tried to programming again.. but nothing...: ERROR AT 0x01F470 Chip = 0x08 buffer = 0x88...
but how many chance do i have that the chip is broken???