MX25L6406E - using Willem 4.1 - what's needed?

Ответить
MoMo
Сообщения:5
Зарегистрирован:Чт ноя 13, 2014 5:19 am
MX25L6406E - using Willem 4.1 - what's needed?

Сообщение MoMo » Чт ноя 13, 2014 6:18 am

Hi Ezo,
Can the Willem v4.1 support programming this chip?

Will the 0.98D12 or latest software recognize the MX25L6406E and work with the v4.1 Willem?

Can you tell me what SPI pin #'s connect to each of the chip pin #'s ..?
...and what, if any, jumpers or switch settings need setting?

Thanks.

Ezo
------
Сообщения:2041
Зарегистрирован:Пн янв 03, 2005 6:50 pm
Откуда:Riga

Re: MX25L6406E - using Willem 4.1 - what's needed?

Сообщение Ezo » Пт ноя 14, 2014 4:16 pm

Can the Willem v4.1 support programming this chip?
Here are different versions of v4.1 . generally yes. SPI 25Cxxx socket, 3.3V support
Will the 0.98D12 or latest software recognize the MX25L6406E and work with the v4.1 Willem?
Serial chips support 0.98d12. Parallel flash memory and EPROMs apply 0.97d12
Can you tell me what SPI pin #'s connect to each of the chip pin #'s ..?
...and what, if any, jumpers or switch settings need setting?
8 pin chips are located 1:1 , apply soic8-dip8 adapter
jumpers - only 3.3V selection for target chip important .
Check voltage in Test H/W mode, activate 32-Vcc and measure pin 8 of 25Cxx socket

MoMo
Сообщения:5
Зарегистрирован:Чт ноя 13, 2014 5:19 am

Re: MX25L6406E - using Willem 4.1 - what's needed?

Сообщение MoMo » Пт ноя 14, 2014 8:49 pm

Thank you VERY much for your reply.

I figured this was the info, but needed to verify with you.

Your forum and all your work is very much appreciated.

Is Dennis still 'with us' or has he also passed, as Willem has?

I'm glad you're still here. 8)

Good-night.

MoMo
Сообщения:5
Зарегистрирован:Чт ноя 13, 2014 5:19 am

Re: MX25L6406E - using Willem 4.1 - what's needed?

Сообщение MoMo » Пт ноя 14, 2014 8:59 pm

Oh..I forgot...one more question.

Is there a photo of the Willem v4.1 silk-screen showing all the writing on-top of the Willem v4.1 programmer.
The board doesn't have all sections properly labeled, and some are unreadable.

I have the one with the relay mod, added on it.

Ezo
------
Сообщения:2041
Зарегистрирован:Пн янв 03, 2005 6:50 pm
Откуда:Riga

Re: MX25L6406E - using Willem 4.1 - what's needed?

Сообщение Ezo » Пн ноя 17, 2014 1:13 am

Like this ?
Вложения
w41_comp.gif
w41_comp.gif (63.16КБ)10990 просмотров

MoMo
Сообщения:5
Зарегистрирован:Чт ноя 13, 2014 5:19 am

Re: MX25L6406E - using Willem 4.1 - what's needed?

Сообщение MoMo » Пн ноя 17, 2014 6:41 pm

Yes...!
Thanks.... :mrgreen: 8)

Ответить