EzoFlash 4.5 problem with paralel devices - need help
I was make EzoFlash 4.5 and it pass all test measured with osilloscope on 32 pin header..
Vpp , Vdd , Vss and all D0-D7 and A0 ..... are present on 32 pin header.
When I probe to read AM29F400BT no ID - nothing...
Also probe PLCC32 W49F002UP , 49LF004 , 39SF020A .. Nothing..
On some PLCC32 bios chip's have ID Fujitsu 0X04...and nothing
On reading that PLCC32 buffer fill first 1/2 of buffer with 04 hex and other with 06 hex...
What is the problem ?
I am not biginer in electronic and have good test equipment so give mi right direction for test...
Also reading PicMicro is OK... for info.
I need programmer special for F100-F400BT devices ... to work good.
Regards Robert
Vpp , Vdd , Vss and all D0-D7 and A0 ..... are present on 32 pin header.
When I probe to read AM29F400BT no ID - nothing...
Also probe PLCC32 W49F002UP , 49LF004 , 39SF020A .. Nothing..
On some PLCC32 bios chip's have ID Fujitsu 0X04...and nothing
On reading that PLCC32 buffer fill first 1/2 of buffer with 04 hex and other with 06 hex...
What is the problem ?
I am not biginer in electronic and have good test equipment so give mi right direction for test...
Also reading PicMicro is OK... for info.
I need programmer special for F100-F400BT devices ... to work good.
Regards Robert
Re: EzoFlash 4.5 problem with paralel devices - need help
Are pins tested one by one with measuring both voltages on/off ?it pass all test measured with osilloscope on 32 pin header..
Vpp , Vdd , Vss and all D0-D7 and A0 ..... are present on 32 pin header.
Looks missing OE signal. Check voltage changes in Test H/W mode, click OE on/off on following test points IC4/1,19, IC7/4, BU3/12.What is the problem ?
Re: EzoFlash 4.5 problem with paralel devices - need help
Problem fix was change IC7 and IC8 - I don't know why but ...it work. (maybe bad luck).
I can read now SST MPF 39SF020A but can't erase or reprogram ....
Also can read Winbond W49F002UP128 bat can't erase or reprogram...
But my focus is AM29F400BT - can't read and no id and one question if anybody know
What is jumper set for PSOP44a adapter for 29F400BT - jumpers on adapter must be ???
[img] [/img]
I am lost.... what next ???
The best best regards to you Ezo.
I can read now SST MPF 39SF020A but can't erase or reprogram ....
Also can read Winbond W49F002UP128 bat can't erase or reprogram...
But my focus is AM29F400BT - can't read and no id and one question if anybody know
What is jumper set for PSOP44a adapter for 29F400BT - jumpers on adapter must be ???
[img] [/img]
I am lost.... what next ???
The best best regards to you Ezo.
Re: EzoFlash 4.5 problem with paralel devices - need help
95% of all problems are in contacts, line break, line short, bad soldering.Problem fix was change IC7 and IC8 - I don't know why but ...it work.
Try recheck.
Are you getting valid ID ?I can read now SST MPF 39SF020A but can't erase or reprogram ....
Also can read Winbond W49F002UP128 bat can't erase or reprogram...
You can find in adapter description or in chip test file.What is jumper set for PSOP44a adapter for 29F400BT - jumpers on adapter must be ???
No jumpers used on adapter for 29F400.
Jumpers Jp1,Jp3, Jp5 on programmer. Jp97/Jp98 - depending from SW.
Jp6 is always ON, currently is test jumper. If random read/write/verify error occurs on serial devices in 5V mode (PIC, ... ) , remove Jp6 and try again. Another way , reduce voltage on target serial chip to 4.3 or 3.6V - most serial eeprom works with 3.6V. I found that only some chips require this mod , not sure in Jp6 usage need. Report me if Jp6 issues found.
What SW do you apply, what is selected chip ? Don't select 29F400 in 16bit mode.But my focus is AM29F400BT
Re: EzoFlash 4.5 problem with paralel devices - need help
All test are finished again and I see something interest..
To I can pass test for A8 up to A16 I mast set A10-A11 high in other way I can't set or reset from A8 to A16 ??????
What is wrong.
I will change 4015 all three and see what will be...
SW 97ja
No vald ID at all for Bios chip's...
Will see and post in next couple hour..
To I can pass test for A8 up to A16 I mast set A10-A11 high in other way I can't set or reset from A8 to A16 ??????
What is wrong.
I will change 4015 all three and see what will be...
SW 97ja
No vald ID at all for Bios chip's...
Will see and post in next couple hour..
Re: EzoFlash 4.5 problem with paralel devices - need help
Find line/soldering short around these lines. No need to change IC.To I can pass test for A8 up to A16 I mast set A10-A11 high in other way I can't set or reset from A8 to A16 ??????
What is wrong.
I will change 4015 all three and see what will be...
Are jumpers in Jp97 position ?SW 97ja
Without test pass , without adress set ID not reachable and read not reliable.No vald ID at all for Bios chip's...
Re: EzoFlash 4.5 problem with paralel devices - need help
Here is finish or maybe not
First at all many thanks Mr. Ezo for extra programmer in for small amount of money !
My problems was :
1. Short on PLCC32 Vpp ro Vcc - Case to break all 74XXX chips ( Great then 5V at Vcc on 74 serie case
damage ).
2. One short on 32 pin socket - case to have problem with set-reset from A8 and up...
3.Do not use These programmer via any of DATA SWITCH for LPT - electronic or mechanic.
4.Cable from LPT to progammer can be maximum of standard 1.5m. Better is short !
5.Put direct to L78705 on IN and OUT pin's to GND two 22-47uF / 25V to prevent 50Hz lake to sistem.As datasheet always write - but we sometime skip that
5.Flux is the last but known problem - I clean it with acetone ( my solution ).
All these is to help to other peoples for easy find problems.
Now I will look to make profesional PCB and package it in box - I will post when finish..
In my case PC is IBM 8188 genuine at dual procesor 3GHz
OS Win XP SP3.
EzoFlash+ V4.5 final revised.
All Bios chip's and HUB-s programming OK .
All Serial devices and PicMicro programmink OK.
Programming of all type Flash memory at last OK !!!
ID for all type of chips OK.
Again thank's Ezo for that extra programmer.
It is better from most CHINA fabricate and easy to make adapter for it.
I have GALEP4 but EzoFlash program AM29F400BT faster and read faster too...
Best best regards Robert
First at all many thanks Mr. Ezo for extra programmer in for small amount of money !
My problems was :
1. Short on PLCC32 Vpp ro Vcc - Case to break all 74XXX chips ( Great then 5V at Vcc on 74 serie case
damage ).
2. One short on 32 pin socket - case to have problem with set-reset from A8 and up...
3.Do not use These programmer via any of DATA SWITCH for LPT - electronic or mechanic.
4.Cable from LPT to progammer can be maximum of standard 1.5m. Better is short !
5.Put direct to L78705 on IN and OUT pin's to GND two 22-47uF / 25V to prevent 50Hz lake to sistem.As datasheet always write - but we sometime skip that
5.Flux is the last but known problem - I clean it with acetone ( my solution ).
All these is to help to other peoples for easy find problems.
Now I will look to make profesional PCB and package it in box - I will post when finish..
In my case PC is IBM 8188 genuine at dual procesor 3GHz
OS Win XP SP3.
EzoFlash+ V4.5 final revised.
All Bios chip's and HUB-s programming OK .
All Serial devices and PicMicro programmink OK.
Programming of all type Flash memory at last OK !!!
ID for all type of chips OK.
Again thank's Ezo for that extra programmer.
It is better from most CHINA fabricate and easy to make adapter for it.
I have GALEP4 but EzoFlash program AM29F400BT faster and read faster too...
Best best regards Robert
Re: EzoFlash 4.5 problem with paralel devices - need help
Good newsHere is finish
My message is : 95% of all problems are in contacts, line break, line short, bad soldering.My problems was :
Strongly recommend check board after production , especially for line breaks.
Check soldering results constantly after each component install on the board.
For ezoflash4v5 - don't place IC fully in on the board. IC pins come wider , higher short risk on top lines between chip pins.
I recomend stabilised power supply or filtered with high value capacitors in output. No need to apply extra capacitor on programmer.Put direct to L78705 on IN and OUT pin's to GND two 22-47uF / 25V to prevent 50Hz lake to sistem
Thanks for known hints reminding !All these is to help to other peoples for easy find problems.
I will appreciate report PM or to my mail adress of any new chip/adapter test result , non-listed in my chip_test file. Report data required for full new line record.All Bios chip's and HUB-s programming OK .
All Serial devices and PicMicro programmink OK.
Programming of all type Flash memory at last OK
Are you able send me high quality picture of your programmer ?
Re: EzoFlash 4.5 problem with paralel devices - need help
Yes I will send you of course all photos from PGM and all adapters which I have and new which I will make soon.
I want to help to we make these programmer to be more robust.
For info Ezo these programmer is better then all type and variation of willem which I was probe...
Regards Robert
IBM P4 dual 3Ghz
Win XP SP3
SW 98D11
EzoFlash V4.5 final
Here are the pic of homemade PCB for EzoFlas v4.5 and couple adapter's by me.
A couple days job and final success ( thank's to autor Mr.Ezo for help).
I was make other's adapters too and probe with 100% success...
Reagards to all ROBERT
I want to help to we make these programmer to be more robust.
For info Ezo these programmer is better then all type and variation of willem which I was probe...
Regards Robert
IBM P4 dual 3Ghz
Win XP SP3
SW 98D11
EzoFlash V4.5 final
Here are the pic of homemade PCB for EzoFlas v4.5 and couple adapter's by me.
A couple days job and final success ( thank's to autor Mr.Ezo for help).
I was make other's adapters too and probe with 100% success...
Reagards to all ROBERT