help error at oxoooooo chip=0x04 buffer =0x04
Clean the pcb and already the problem does not appear.
But divice id It recognizes
id=0xFF
0XFF
erase divice ok
read divice ok
blank check ok
program no functionally
Mistake appears error at 0x000000 chip 0xFF buffer 0x21
no can be programming .
It tries chip amic A29002IT
And it works ok
He forgives for my inglish
I speak the Spanish
But divice id It recognizes
id=0xFF
0XFF
erase divice ok
read divice ok
blank check ok
program no functionally
Mistake appears error at 0x000000 chip 0xFF buffer 0x21
no can be programming .
It tries chip amic A29002IT
And it works ok
He forgives for my inglish
I speak the Spanish
Re: help error at oxoooooo chip=0x04 buffer =0x04
He does not identify chip
0x21
0xFF
read ok
erase ok
blank check ok
but It cannot programme
error at 0x000001 chip =0xff buffer 0x69
That means this?.
chip bad?
adapter PLCC-32_B2 bad ?
note:adapter dip 32 -A funtionally ok
0x21
0xFF
read ok
erase ok
blank check ok
but It cannot programme
error at 0x000001 chip =0xff buffer 0x69
That means this?.
chip bad?
adapter PLCC-32_B2 bad ?
note:adapter dip 32 -A funtionally ok
Re: help error at oxoooooo chip=0x04 buffer =0x04
Which is the voltage in of reading and programming in pines 25.29.32.31 of adapter plcc 32 b2?
Re: help error at oxoooooo chip=0x04 buffer =0x04
What chips are tested with dip32a1 ? What chip ID are you getting ?
I suppose programmer failure, because no correct ID reply.
Go again Test H/W and check all signals one by one. Use check table, find in Guides.
I suppose programmer failure, because no correct ID reply.
Go again Test H/W and check all signals one by one. Use check table, find in Guides.
Re: help error at oxoooooo chip=0x04 buffer =0x04
you can program other device with this programmer ?
or with other device have same problem ?
you sure your programmer working good ?
or with other device have same problem ?
you sure your programmer working good ?
Re: help error at oxoooooo chip=0x04 buffer =0x04
Programme W49F002U WINBOND
A29002IT AMIC
With adapter dip 32a and I work ok.
But W39V040apz WINBOND with adapter plcc 32b does not detect ID .
Vcc 5v and not 4.3v in BU6/20 .
A29002IT AMIC
With adapter dip 32a and I work ok.
But W39V040apz WINBOND with adapter plcc 32b does not detect ID .
Vcc 5v and not 4.3v in BU6/20 .
Re: help error at oxoooooo chip=0x04 buffer =0x04
if id not detect i think your chip is damaged
try with new chip
or is possible your adapter have problem and damaged chip
try with new chip
or is possible your adapter have problem and damaged chip
Re: help error at oxoooooo chip=0x04 buffer =0x04
but ready and erase chip ok
Re: help error at oxoooooo chip=0x04 buffer =0x04
blank check is ok ?
if is not your erase not ok
if is not your erase not ok
Re: help error at oxoooooo chip=0x04 buffer =0x04
yes, blank check is ok
Re: help error at oxoooooo chip=0x04 buffer =0x04
again try erase
after erase read chip and check checksum and buffer is empty
you use ezo4v4 or ezo4v5 ?
i think you try program new chip with this adapter
you have another adapter plcc_b2 ?
after erase read chip and check checksum and buffer is empty
you use ezo4v4 or ezo4v5 ?
i think you try program new chip with this adapter
you have another adapter plcc_b2 ?
Re: help error at oxoooooo chip=0x04 buffer =0x04
use ezo4v4
- Вложения
-
- program.GIF (81.15КБ)6060 просмотров
-
- id.GIF (75.74КБ)6060 просмотров
-
- check blank.GIF (73.19КБ)6060 просмотров
Re: help error at oxoooooo chip=0x04 buffer =0x04
Seems programming works, but with random error.
If error reply chip 0xFF buffer 0x.., try overwrite.
Another options.
Remove temporary both capacitors 100n from plcc32b2.
Try with software 0.97d12c3
If error reply chip 0xFF buffer 0x.., try overwrite.
Another options.
Remove temporary both capacitors 100n from plcc32b2.
Try with software 0.97d12c3
Re: help error at oxoooooo chip=0x04 buffer =0x04
tets whith capacitor removed
Re: help error at oxoooooo chip=0x04 buffer =0x04
In some ocacion it recognizes id but then already not.
- Вложения
-
- Dibujo.PNG (74.73КБ)6049 просмотров